How do I reset my Fisher and Paykel double drawer dishwasher?
How do I reset my Fisher and Paykel double drawer dishwasher?
Reset Procedures for the Fisher & Paykel Dishwasher
- Press and hold the button decorated with the key and lock image for five seconds.
- Press the power button to turn off power to the Fisher & Paykel dishwasher.
- Wait a few minutes and then press the power button to restore power.
What does F1 mean on a sharp dishwasher?
Sharp Dishwasher Error Codes
| Error Codes | Solution |
|---|---|
| F2 | The waste water in the machine cannot be discharged. |
| F8 | Heater error |
| F1 | Alarm is active against water overflow |
| FE | Faulty electronic card |
Why is my Fisher and Paykel dishwasher not draining?
Straighten any kinks along the hose that drains water from your DishDrawer™. If the kinks return, you may need to replace the hose. Clean the filter plate/drain filter. Aim to clean your DishDrawer™ at least once per month, including the drain filter plates.
How do I fix E6 error on my dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
Where is the flood switch on a dishwasher?
A dishwasher’s float switch will sit below the float assembly. So find your float assembly inside your dishwasher, and your switch will be located directly below it in the access area. It will likely be either on the left or the right hand side. There are going to be two wires connected to the float switch.
How do you run a diagnostic on a Fisher Paykel dishwasher?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
How do you unlock a Fisher Paykel dishwasher drawer?
Press and hold the LOCK button for 3 seconds to lock or unlock the control panel.
How do I fix the F2 error on my dishwasher?
The F2 error is linked to water, weather it’s for intake our outtake. First we check if the water is going through the tap. In the dishwasher we pour 2-3 liters of water, close it and hold the reset button for a bit and that’s it. The machine should start working on the last faze where it takes out the water.
How do I fix F5 error on sharp dishwasher?
The F5 code means that the machine is not draining. Either there is something blocking the drain line or the drain pump is defective. I would first check the outlet where the drain line attaches to. Take the drain hose off the syphon gap or trap and see if the water will drain out of the machine into a bucket.
What does E6 mean on a dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
What does F1 mean on Fisher Paykel dishwasher?
F1 on Fisher & Paykel Dishwashers. F1 means that there is water in the base pan below the bottom drawer. This usually happens because something was stacked too high in one of the drawers when it was running and this caused the lid to not seal up when the drawer was shut.
What makes a Fisher and Paykel double dishwasher so good?
With the ergonomic convenience of drawer accessibility and split-load capability, the Double DishDrawer™ Dishwasher is perfect for a busy household. A traditional format with large open space and convenient drawer rack for easy stacking.
How many days of dishes in a Fisher Paykel DishDrawer?
We entertain frequently and use both drawers at those times. They can run at the same time or separately. When it is just the two of us, one drawer is adequate to hold several days’ worth of dishes. The drawers have few moving parts, are very quiet, and are both water and energy efficient.
Where is the drain drawer on a Fisher and Paykel dishwasher?
Depress the two square tabs on either side of the drawer right behind the front panel to continue removing the drawer as far out as you can, then lift the drawer up and out, tilting at a slight angle to remove it. Set an old towel in the drain pan to soak up the excess water.