Guidelines

How do I reset my juniper to factory settings?

How do I reset my juniper to factory settings?

Restore Juniper SRX210 to factory default configuration

1. Power on the Juniper SRX210 by plugging it to the power adapter.
2. Using a pin or paperclip, press and hold the RESET CONFIG button for 15 seconds.
3. Wait about 2 minutes while the Juniper SRX210 restores to the factory default settings.

How do I reset my juniper EX2200 to factory settings?

Knowledge Base

1. In Junos 11.1 or later, the method to reset to the factory default configuration for EX2200, is to use the request system zeroize Junos CLI command to erase all data, including configuration and log files.
2. After executing the command, the EX2200 will be rebooted with the factory default configuration.

What is the default password for Juniper SRX?

Note: If you are looking for a default password, there is no default password in SRX. A new SRX out of the box has the root user with no password. 1) Reboot the box and press SPACE when you see the following screen to get to the loader prompt.

How do I factory reset my SRX1500?

Using the RESET CONFIG Button on the SRX1500 Services Gateway. If a configuration fails or denies management access to the services gateway, you can use the RESET CONFIG button to restore the services gateway to the factory-default configuration. The button is recessed to prevent it from being pressed accidentally.

How do I reset my juniper ex3200 to factory settings?

Reverting to the Default Factory Configuration by Using the Menu Button

1. Press the Menu button until you see MAINTENANCE MENU on the panel.
2. Press the Enter button.
3. Press Menu until you see FACTORY DEFAULT.
4. Press Enter. The display says RESTORE DEFAULT?
5. Press Enter.

How do I reset Juniper?

When the MAIN MENU (Maintenance menu) appears, press the Enter button. Select the SYSTEM REBOOT option and press the Enter button. To exit the menu without rebooting the switch, press the Menu button again.

How do I reset my juniper EX2200 without password?

9. RE: Unable to reset password on EX2200

1. Obtain console access.
2. Power off the system and boot it up in single user mode.
3. Next, the system will run the normal bootup process.
4. The system will finish booting up and display the root>prompt.
5. Enter configuration mode and edit or delete the root authentication password.

How do I reset my srx240 to factory settings?

You can use the Reset Config button on the front panel of the SRX device to reset the device to its factory default configuration. The Reset Config button is recessed to prevent it from being pressed accidentally; so you need to insert a small probe (for example, a straightened paper clip) to press the button.

How do I reset my juniper srx320?

To press the RESET CONFIG button, insert a small probe (such as a straightened paper clip) into the pinhole on the front panel. By default, pressing and quickly releasing the RESET CONFIG button loads and commits the rescue configuration through the J-Web interface or the CLI.

How do I factory reset my juniper EX4300?

How to return to factory default…Juniper Networks?

In Junos 11.1 or later, the method to reset to the factory default configuration for EX2200, is to use the request system zeroize Junos CLI command to erase all data, including configuration and log files. After executed the command, the EX2200 will be rebooted with the factory default configuration.

Is there a way to factory reset juniper SRX device?

Sometimes administrators working on Junos platform need to reset the SRX device to factory default. Juniper has quite a few options to meet this requirement – one via manually resetting SRX to default setting and one via issuing CLI command. USING THE RESET BUTTON –.

How to load a previous configuration file in Juniper?

See Loading a Previous Configuration File (CLI Procedure). The default factory configuration contains the basic configuration settings. This is the first configuration of the switch and it is loaded when the switch is first installed and powered on.

Where are the buttons on a juniper network switch?

To set the switch to the factory default configuration, use the buttons to the right of the LCD on the front panel of the switch as shown in Figure 1